ENDURO COMPUTER MOUNT

Regular Price
$17.00
Sale Price
$17.00
Regular Price
Out of Stock
Unit Price
per 

Shape/Computer type: Garmin Type B

Finish: Black

1014G

Details

Sticks Like $%*? To a Blanket!

Self-adhesive computer mount using 3M VHB tape (very high bond)

Designed to fit onto your top tube behind your stem for maximum protection and less distraction.

FIT OPTIONS

Type A for flat or slightly curved top tubes  Maximum curve of up to 3mm drop 12mm from the centre line. Most carbon and aluminium bikes require type A. The base of Type A's has a flat centre with curved 'wings' that flex to the top tube profile, including going all the way to flat.
Some customers have been surprised that the Type A has a pronounced curve to the base, be assured that it will flex to flat. Type A has a single dot on the spine.

Type B for round and heavily curved top tubes. Works on round tubes of 34mm, smaller diameters will require the mount being clamped in place overnight in order to ensure a good bond. Type B has 2 dots on the spine.

 

Supplied with alcohol wipe to clean the area to be attached to.

Manufactured in-house in nylon using Multi Jet Fusion additive manufacturing and shot peened for surface toughness and quality.

CERAKOTE COLOUR OPTIONS

Currently available for Garmin Type A only
Cerakote is a ultra thin ceramic coating which is hydrophobic, chemical and scratch resistant.

Top left to bottom right in image:

Blue Titanium (metallic flecks)
Tequila Sunrise (metallic flecks)
Burnt Bronze (metallic flecks)
Firehouse Red (satin)
Testing has shown that the coating on the enduro mounts are resistant to wear, however the tip of the little Garmin engagement tabs ( at 3 and 9 o'clock) will wear down to black.

 

IMPORTANT - Check there is clearance from the underside of bars/stem to the top tube:

 

 


Sticks Like $%*? To a Blanket!

Self-adhesive computer mount using 3M VHB tape (very high bond)

Designed to fit onto your top tube behind your stem for maximum protection and less distraction.

FIT OPTIONS

Type A for flat or slightly curved top tubes  Maximum curve of up to 3mm drop 12mm from the centre line. Most carbon and aluminium bikes require type A. The base of Type A's has a flat centre with curved 'wings' that flex to the top tube profile, including going all the way to flat.
Some customers have been surprised that the Type A has a pronounced curve to the base, be assured that it will flex to flat. Type A has a single dot on the spine.

Type B for round and heavily curved top tubes. Works on round tubes of 34mm, smaller diameters will require the mount being clamped in place overnight in order to ensure a good bond. Type B has 2 dots on the spine.

 

Supplied with alcohol wipe to clean the area to be attached to.

Manufactured in-house in nylon using Multi Jet Fusion additive manufacturing and shot peened for surface toughness and quality.

CERAKOTE COLOUR OPTIONS

Currently available for Garmin Type A only
Cerakote is a ultra thin ceramic coating which is hydrophobic, chemical and scratch resistant.

Top left to bottom right in image:

Blue Titanium (metallic flecks)
Tequila Sunrise (metallic flecks)
Burnt Bronze (metallic flecks)
Firehouse Red (satin)
Testing has shown that the coating on the enduro mounts are resistant to wear, however the tip of the little Garmin engagement tabs ( at 3 and 9 o'clock) will wear down to black.

 

IMPORTANT - Check there is clearance from the underside of bars/stem to the top tube:

 

 


Weight:

Material: MJF Nylon PA12 - manufactured in house

When fitting the adhesive needs a temperate of at least 20 degrees C to cure properly. After fitting the mount should be left overnight before riding.

See videos in image section of install and uninstall instructions. Also available here.

Recommended for smaller series computers no larger than Wahoo Element Roam, Garmin 500 series. Larger computer are vulnerable to knee knocks. As with any mount, in case of a crash, we recommend looping the computer's tether around the top tube.

To remove, pry the mount off from one end. The adhesive pad should remain in one piece but cannot be reused. Replacement VHB pads are available here. It helps to heat with a hairdryer or leave in a warm room beforehand. 

We hate it went a product has to be junked when a part can't be replaced. If spares aren't listed email us and we'll see if we can help.

Replacement VHB pads are available here

Customer Reviews

Based on 85 reviews
89%
(76)
8%
(7)
1%
(1)
0%
(0)
1%
(1)
D
DAVID NEILSON
Fantastic mount

I am very happy with my 76er. Pro tip: if you want to move it from it's original position, Scotch / 3m double-sided tape from the hardware store worked great.

J
Joe Mama
More robust then i thought it would be

Got the 76project mount for my ibis ripmo... First thing i noticed was it was stronger and more robust then i thought it would be. When i ordered i thought "great here is going to be another cheap 3d printed plastic thingy that is going to break right away".. So far it couldnt be further from that.. Very stiff and stable... I ordered the rounded version cause my rimpo top was rounded. But i should have gotten the flat version. The rounded version is really for true round tubes and the flat is more for the very slightly rounded top.. So if you have a ripmo or a carbon bike with a fat semi round top-- just get the flat version..

Would i buy again? Yes, 100%..

C
Chase Litwa
Wahoo type a black

I love this mount. I came from the basic wahoo mount that hangs off the bars, in front of the stem. This works great and keeps everything clean and tidy.

A
Adam

Looks and works great. Garmin Edge 540 feels very secure. This location is going to be great.

J
JF
Great product

A great solution to short stems on trail and enduro bikes to get the Garmin out of the way.