ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT
ENDURO COMPUTER MOUNT

ENDURO COMPUTER MOUNT

$17.00
$17.00
Out of Stock

Shape/Computer type: Garmin Type A

Finish: Black

1040G

Details

Sticks Like $%*? To a Blanket!

Self-adhesive computer mount using 3M VHB tape (very high bond)

Designed to fit onto your top tube behind your stem for maximum protection and less distraction.

FIT OPTIONS

Type A for flat or slightly curved top tubes  Maximum curve of up to 3mm drop 12mm from the centre line. Most carbon and aluminium bikes require type A. The base of Type A's has a flat centre with curved 'wings' that flex to the top tube profile, including going all the way to flat.
Some customers have been surprised that the Type A has a pronounced curve to the base, be assured that it will flex to flat. Type A has a single dot on the spine.

Type B for round and heavily curved top tubes. Works on round tubes of 34mm, smaller diameters will require the mount being clamped in place overnight in order to ensure a good bond. Type B has 2 dots on the spine.

 

Supplied with alcohol wipe to clean the area to be attached to.

Manufactured in-house in nylon using Multi Jet Fusion additive manufacturing and shot peened for surface toughness and quality.

CERAKOTE COLOUR OPTIONS

Currently available for Garmin Type A only
Cerakote is a ultra thin ceramic coating which is hydrophobic, chemical and scratch resistant.

Top left to bottom right in image:

Blue Titanium (metallic flecks)
Tequila Sunrise (metallic flecks)
Burnt Bronze (metallic flecks)
Firehouse Red (satin)
Testing has shown that the coating on the enduro mounts are resistant to wear, however the tip of the little Garmin engagement tabs ( at 3 and 9 o'clock) will wear down to black.

 

IMPORTANT - Check there is clearance from the underside of bars/stem to the top tube:

 

 


Sticks Like $%*? To a Blanket!

Self-adhesive computer mount using 3M VHB tape (very high bond)

Designed to fit onto your top tube behind your stem for maximum protection and less distraction.

FIT OPTIONS

Type A for flat or slightly curved top tubes  Maximum curve of up to 3mm drop 12mm from the centre line. Most carbon and aluminium bikes require type A. The base of Type A's has a flat centre with curved 'wings' that flex to the top tube profile, including going all the way to flat.
Some customers have been surprised that the Type A has a pronounced curve to the base, be assured that it will flex to flat. Type A has a single dot on the spine.

Type B for round and heavily curved top tubes. Works on round tubes of 34mm, smaller diameters will require the mount being clamped in place overnight in order to ensure a good bond. Type B has 2 dots on the spine.

 

Supplied with alcohol wipe to clean the area to be attached to.

Manufactured in-house in nylon using Multi Jet Fusion additive manufacturing and shot peened for surface toughness and quality.

CERAKOTE COLOUR OPTIONS

Currently available for Garmin Type A only
Cerakote is a ultra thin ceramic coating which is hydrophobic, chemical and scratch resistant.

Top left to bottom right in image:

Blue Titanium (metallic flecks)
Tequila Sunrise (metallic flecks)
Burnt Bronze (metallic flecks)
Firehouse Red (satin)
Testing has shown that the coating on the enduro mounts are resistant to wear, however the tip of the little Garmin engagement tabs ( at 3 and 9 o'clock) will wear down to black.

 

IMPORTANT - Check there is clearance from the underside of bars/stem to the top tube:

 

 


Weight:

Material: MJF Nylon PA12 - manufactured in house

When fitting the adhesive needs a temperate of at least 20 degrees C to cure properly. After fitting the mount should be left overnight before riding.

See videos in image section of install and uninstall instructions. Also available here.

Recommended for smaller series computers no larger than Wahoo Element Roam, Garmin 500 series. Larger computer are vulnerable to knee knocks. As with any mount, in case of a crash, we recommend looping the computer's tether around the top tube.

To remove, pry the mount off from one end. The adhesive pad should remain in one piece but cannot be reused. Replacement VHB pads are available here. It helps to heat with a hairdryer or leave in a warm room beforehand. 

We hate it went a product has to be junked when a part can't be replaced. If spares aren't listed email us and we'll see if we can help.

Replacement VHB pads are available here

Customer Reviews

Based on 89 reviews
90%
(80)
8%
(7)
1%
(1)
0%
(0)
1%
(1)
T
Thomas Teabo
Excellent

My Garmin mount works perfectly. I will always use this product from my Garmin Mounts

A
Anthony Eng
Works perfect!

First thing to keep in mind: Clean twice, measure twice, stick once! I didn't have any issues since I ordered the right mount (slightly rounded/mostly flat) for my Ripmo. Plus the V2 Ripmo has a centered logo that really helps. I can tell that if you mis-apply the mount, that sucker will be hard to remove. I used it twice so far and it took some getting used to because I used to have a handlebar mount -- I now have to look farther down. But I really enjoy the cleaner bar/cockpit setup. Well worth it in my opinion!

K
Kade Brantingham
Enduro computer mount

Overall super stoked with the mount so far. I got the “flat” version to put on the top tube of my trek slash and trek fuel EX. The mount is definitely a little more curved than i would like as both top tubes are very flat. But with some firm pressure it has adhered just fine. Would recommend to anyone looking for an option like this.

J
Jerome B
Best news about crashing!

Learned first hand that the tabs on the enduro mount break before the tabs on the computer. I have a tether on my Wahoo ELEMNT bolt, so was able to quickly get it replaced and re-mounted

D
DAVID NEILSON
Fantastic mount

I am very happy with my 76er. Pro tip: if you want to move it from it's original position, Scotch / 3m double-sided tape from the hardware store worked great.

123